Objective Practice on Machine Design Engineering - Set 33 - ObjectiveBooks
Objective Practice on Machine Design Engineering - Set 33

Objective Practice on Machine Design Engineering - Set 33

Practice Test: Question Set - 33

1. In worm gears, the angle between the tangent to the pitch helix and an element of the cylinder, is known as
    (A) Helix angle
    (B) Pressure angle
    (C) Pitch lead angle
    (D) None of these
2. The yield point in static loading is __________ as compared to fatigue loading.
    (A) Higher
    (B) Lower
    (C) Same
    (D) None of these
3. The resilience of a bolt may be increased by
    (A) Increasing its shank diameter
    (B) Increasing its length
    (C) Decreasing its shank diameter
    (D) Decreasing its length
4. The velocity factor for ordinary cut gears operating at velocities up to 12.5 m/s is equal to
    (A) 0.75/(0.75 + √v)
    (B) 3/(3 + v)
    (C) 4.5/(4.5 + v)
    (D) 6/(6 + v)
5. The bearings of medium series have capacity __________ over the light series.
    (A) 10 to 20%
    (B) 20 to 30%
    (C) 30 to 40%
    (D) 40 to 50%
6. The square threads are usually found on
    (A) Spindles of bench vices
    (B) Railway carriage couplings
    (C) Feed mechanism of machine tools
    (D) Screw cutting lathes
7. Multiple threads are used to secure
    (A) Low efficiency
    (B) High efficiency
    (C) High load lifting capacity
    (D) High mechanical advantage
8. Which of the following statement is correct?
    (A) The cold rolled shafting is stronger than hot rolled shafting
    (B) The hot rolled shafting is stronger than cold rolled shafting
    (C) The cold rolled and hot rolled shafting are equally strong
    (D) The shafts are not made by rolling process
9. The speed of the sprocket reduces as the chain pitch __________ for a given number of teeth.
    (A) Increases
    (B) Decreases
    (C) Remain same
    (D) None of these
10. The permissible stress in the fillet weld is 100 N/mm². The fillet weld has equal leg lengths of 15 mm each. The allowable shearing load on the weldment per cm length of the weld is
    (A) 7.5 kN
    (B) 10.6 kN
    (C) 15 kN
    (D) 22.5 kN
11. The smallest diameter of an external or internal screw thread is known as
    (A) Minor diameter
    (B) Major diameter
    (C) Pitch diameter
    (D) None of these
12. The shock absorbing capacity of a bolt may be increased by
    (A) Increasing its shank diameter
    (B) Decreasing its shank diameter
    (C) Tightening the bolt properly
    (D) Making the shank diameter equal to core diameter of thread
13. The piston pin bearings in heavy duty diesel engines are
    (A) Needle roller bearings
    (B) Tapered roller bearings
    (C) Spherical roller bearings
    (D) Cylindrical roller bearings
14. The tension on the slack side of the belt is __________ the tension on the tight side of the belt.
    (A) Equal to
    (B) Less than
    (C) Greater than
    (D) None of these
15. In skew bevel gearing, the axes of shafts are
    (A) Intersecting and the teeth are curved
    (B) Non-intersecting and nonparallel and the teeth are curved
    (C) Non-intersecting and non-parallel and the teeth are straight
    (D) None of the above
Show and hide multiple DIV using JavaScript View All Answers

 Next Tests: